Grinding of composite cores using diamond burs with different grit sizes: the effects on the retentive strength of zirconia crowns

Aim: To evaluate the retention of Y-TZP crowns cemented in aged composite cores ground with burs of different grit sizes. Methods: Sixty composite resin simplified full-crown preparations were scanned, while 60 Y-TZP crowns with occlusal retentions were milled. The composite preparations were stored for 120 days (wet environment-37°C) and randomly distributed into three groups (n=20) according to the type of composite core surface treatment. The groups were defined as: CTRL (control: No treatment), EFB (extra-fine diamond bur [25µm]), and CB (coarse diamond bur [107µm]). The grinding was performed with an adapted surveyor standardizing the speed and pressure of the grinding. The intaglio surfaces on the crowns were air-abraded with silica-coated alumina particles (30 µm) and then a silane was applied. The crowns were cemented with self-adhesive resin cement, thermocycled (12,000 cycles; 5/55°C), stored (120 days) and submitted to a retention test (0.5mm/min). The retentive strength data (MPa) were analyzed using one-way analysis of variance and Tukey test, as well as Weibull analysis. Failures were classified as 50C (above 50% of cement in the crown), 50S (above 50% of cement in the substrate) and COE (composite core cohesive failure). Results: No statistical difference was observed among the retention values (p=0.975). However, a higher Weibull modulus was observed in the CTRL group. The predominant type of failure was 50S (above 50% of cement in the substrate composite). Conclusion: The retention of zirconia crowns was not affected by grinding using diamond burs with different grit sizes (coarse/extra-fine) or when no grinding was performed

Endodontic sealers and post-endodontic waiting time affect the bond strength of the fiber posts / Cimentos endodônticos e tempo de espera após endodontia afeta a resistência de união de pinos de fibra

Introduction: The resistance adhesive of a fiber post can be affected by several factors, such as the endodontic sealer and post-endodontic waiting time. Objective: The aim of this study was to evaluate the effect of different endodontic sealers and two different post-endodontic waiting times on the bond strength of fiber posts. Material and method: Seventy-two bovine teeth were endodontically treated and filled using three endodontic sealers: eugenol-based, epoxy resin-based, or mineral trioxide aggregate-based. The specimens were stored at 37°C for 24 hours or for 30 months. After the respective storage times, the root canals were prepared for luting fiber posts using RelyX U200. Push-out tests and analysis of failures were performed. The push-out data were analyzed by two-way analysis of variance to compare the effects of the endodontic sealer and with the t-test to compare the effects of post-endodontic waiting time. Result: The AH Plus sealer yielded the highest bond strength values at 30 months post-endodontics (11.26 Mpa) (p < 0.05), however no had difference with Endofill sealer at the same time. Endofill and MTA Fillapex sealers did not differ significantly in their effects, irrespective of the post-endodontic waiting time. Conclusion: In conclusion, the endodontic sealer used and post-endodontic waiting time affect the adhesive resistance of fiber posts. The adhesion increases significantly when the fiber post is cemented 30 months after the root canal filling, while the adhesion is reduced when cementing immediately after root canal treatment, in particular for eugenol-based endodontic sealers.

Introdução: A resistência de união de um pino de fibra pode ser afetada por vários fatores, como o cimento endodôntico e o tempo de espera pós-endodontia. Objetivo: Avaliar o efeito de diferentes cimentos endodônticos e dois tempos de espera pós-endodontia na resistência de união de pinos de fibra. Material e método: Setenta e dois dentes bovinos foram tratados endodonticamente e obturados usando três cimentos endodônticos: à base de eugenol, à base de resina epóxia ou à base de mineral trióxido agregado. Os espécimes foram armazenados a 37 ° C por 24 horas ou por 30 meses. Após, os canais radiculares foram preparados para cimentação dos pinos de fibra usando o RelyX U200. Foram realizados testes de push-out e análise de falhas. Os dados foram analisados por análise de variância bidirecional e com o teste t. Resultado: O cimento AH Plus obteve os maiores valores de resistência de união aos 30 meses pós-endodontia (11,26 Mpa) (p <0,05), no entanto, não houve diferença com o cimento Endofill no mesmo tempo. Os cimentos Endofill e MTA Fillapex não diferiram significativamente em seus efeitos, independentemente do tempo de espera pós-endodontia. Conclusão: O cimento endodôntico utilizado e o tempo de espera pós-endodontia afetam a resistência adesiva dos pinos de fibra. A adesão aumenta significativamente quando o pino de fibra é cimentado 30 meses após a obturação do canal radicular, enquanto a adesão é reduzida ao cimentar imediatamente após o tratamento do canal radicular, principalmente para cimentos endodônticos à base de eugenol.

Retention strength of ball-attachment titanium post for removable partial denture or overdenture

Aim: To evaluate the retention of an endodontic titanium postwith a spherical head for removable partial denture or overdentureattachment according to surface treatment type. Methods: Sixtyhealthy single-rooted teeth, sectioned at the enamel/cementumjunction, were treated endodontically and steadily fixed in theembedding acrylic resin. The titanium posts were subdivided intofour groups: control, no surface treatment (Ctrl); posts with macroretentivegrooves (MR); air abrasion of the post surface (AB); andposts with macro-retentive grooves and air abrasion of the postsurface (MR+AB). The posts were luted in the root canal usingself-adhesive dual resin cement. Pull-out testing was performedusing a universal testing machine until complete detachment wasachieved. After pull-out testing, the metallic posts were examinedunder an optical microscope and the failures were classifiedbased on the cement distribution pattern on the extracted posts:0, no cement left on the post (cement/post failure); 1, postsurface partially covered by adhered cement (post/cement anddentin/cement mixed failure); 2, post surface completely coveredby cement (dentin/cement failure). The retention data wereanalyzed by one-way ANOVA, Bonferroni­Dunn test (p<0.05)and Weibull analysis. Results: AB showed the highest retentionvalue (485.37±68.36), followed by MR+AB (355.80±118.47), MR(224.63±42.54) and Ctrl (113.12 ± 51.32). AB and MR showedthe highest Weibull moduli. Conclusions: The data indicatedthat air abrasion alone could significantly increase the retentionof titanium posts/attachments for use with overdentures orremovable partial denture

Fracture load and shear stress of prefabricated glass fiber posts

Aim: This study evaluated the fracture load and pattern failure of different prefabricated glass fiber posts (GFPs) of the same diameter. Methods: Seventy-eight (n=13 for six groups) GFPs of 1.6 mm coronal diameter of different brands were evaluated­ Exacto (Angelus), Power Post (BM4), White Post DC (FGM), HiRem (Overfibers), MAQ (Maquira), and SD (Supordont). The posts were subjected to fracture load testing (45° of inclination and 1 mm/min until fracture). Each factor (load (N) and shear stress (MPa)) was analyzed separately using one-way ANOVA followed by the Tukey test (α=0.05). Results: The type of failure was evaluated on a stereomicroscope (×10). The Power Post samples presented higher values of fracture load (p<0.001) followed by Maquira fiber post, White Post , HiRem, Superpost, and the Exacto posts. The failure pattern observed was intralaminar mode II in-plane shear, such as a failure occur parallel to fibers. Conclusion: Despite the same diameter of GFPs, the fracture load and shear resistance were brand-dependent

Effect of several repair techniques on the bond strength between composite resin and degraded Y-TZP ceramic / Efeito de várias técnicas de reparo na resistência de união entre resina composta e zircônia degradada

Objective: To evaluate the bond strength of different repair treatments for composite resin to aged Y-TZP ceramics. Material and Methods: Zirconia blocks were cut into smaller specimens, sintered according to manufacturer's recommendations (final dimensions of 4×4×3 mm), and randomly allocated into nine groups (n=15) according to the surface treatment and presence/ absence of aging of the substrate (subjected to lowtemperature degradation - LTD), as follows: without LTD (Control: without treatment; TBS: tribochemical silica coating + silane + adhesive); with LTD (Control-LTD: without treatment; TBS-LTD: TBS with hydrothermal degradation; MoS-LTD: Monobond S + adhesive; MoPLTD: Monobond Plus + adhesive; MZP-LTD: Metal/ Zirconia Primer + adhesive; USB-LTD: Single Bond Universal; AP-LTD: Alloy primer + adhesive). LTD was simulated in an autoclave (134 °C, 2 bar, 5 h). The ceramic blocks were embedded in PVC cylinders with a self-curing acrylic resin; each surface treatment protocol was performed; a composite resin cylinder ( : 3.25 mm and height: 3 mm) was then build-up using split metallic matrices. All the specimens were aged (thermocycling + storage in water for 90 days) and subjected to the shear bond strength test using a universal testing machine (1 mm/min). The failure mode was classified into four types: adhesive, composite resin cohesive fracture, ceramic cohesive fracture, and mixed. The bond strength values were subjected to Mann­Whitney test. Results: Only air-abraded samples (TBS and TBS­LTD) survived thermocycling. More than 80% of the samples of the other groups presented pre-test failures. TBS groups presented higher values of bond strength (3.94) compared to TBSLTD (0.96). The predominant type of failure for the surviving samples were adhesive. Conclusion: Air particle abrasion is mandatory to improve the bond strength of the Y-TZP substrate; an aged substrate presents an even more unfavorable scenario for adhesion. (AU)

Objetivo: Avaliar a resistência de união ao cisalhamento gerada por diferentes técnicas de reparo em resina composta aderida em zircônia envelhecida (sujeita a degradação a baixa temperatura - LTD). Material e Métodos: blocos de zircônia foram seccionados em espécimes, sinterizados de acordo com o fabricante (dimensões finais de 4x4x3 mm), e aleatorizados em nove grupos (n=15) de acordo com o tratamento de superfície e presença/ausência de envelhecimento do substrato (LTD), conforme: sem LTD (Control: sem tratamento; TBS: tribosilicatização + silano + adesivo); com LTD (Control-LTD: Monobond S + adesivo; MoP-LTD: Monobond plus + adesivo; MZPLTD: Meta/Zirconia primer + adesivo). LTD foi simulada em autoclave (134 °C, 2 bar, 5 h). Os blocos de cerâmica foram embutidos em cilindros de PVC com resina acrílica autopolimerizável; cada tratamento de superfície foi realizado; um cilindro de resina composta ( : 3,25 mm 3 mm de altura) foi confeccionado usando matrizes metálicas bipartidas. Todos os espécimes foram envelhecidos (termociclagem + armazenagem em água por 90 dias) e sujeitos ao teste de cisalhamento usando um equipamento de teste universal (1 mm/ min). O modo de falha foi classificado em quatro grupos: adesivo, fratura coesiva em resina composta, fratura coesiva da cerâmica, e mista. Os valores de adesão foram sujeitos ao teste de Mann-Whitney. Resultados: somente as amostras jateadas (TBS e TBSLTD) sobreviveram a termociclagem. Mais que 80% dos espécimes dos outros grupos apresentaram falhas préteste. Os grupos TBS apresentaram os maiores valores de resistência ao cisalhamento (3,94) comparado com TBS-LTD (0,96). Os tipos predominantes de falha para os espécimes sobreviventes foi adesiva. Conclusão: o jateamento é recomendável para aumentar a resistência adesiva à zircônia; um substrato envelhecido apresenta um cenário mais desfavorável de adesão. (AU)

Influence of elastic modulus of intraradicular posts on the fracture load of roots restored with full crowns / Influência do modulo de elasticidade de retentores intrarradiculares na carga para fratura de raízes restauradas com coroas totais

Objective: This study aimed to evaluate the fracture load and displacement of roots restored with posts of different elastic modulus. Material and method: Thirty-six replicas of epoxy resin mixed with glass microfibers were made from an endodontically-treated human premolar root prepared to a length of 12 mm with a custom drill, leaving the apical 4 mm unprepared. Replicas were randomly restored with (n = 12): FP-LM (fiber post with low elastic modulus- 50 GPa), FP-HM (fiber post with high elastic modulus - 67 GPa) and MP (metallic post - 208 GPa), using self-curing adhesive and dual resin cement. Cores were built up with composite resin and metallic crowns were cemented in all the roots with self-adhesive resin cement with self-curing mode. Specimens were subjected to a fracture load test (45° inclination/0.5 mm/min) and displacement was registered at 100 N. Result: One-way ANOVA showed that elastic modulus of the post did not affect the fracture load means (p = 0.203) (FP-LM: 237.4 ± 65.11 N; FP-HM: 236.7 ± 92.85 N; MP: 295.8 ± 108.7 N) but was statistically significant for the displacement (p < 0.00): Tukey's test showed that FP-LM displacement mean (0.81 ± 0.15 mm) was significantly higher than those for FP-HM (0.46 ± 0.26 mm; p = 0.00) and MP (0.62 ± 0.07 mm; p = 0.04). Conclusion: Posts with different elastic modulus exhibit similar fracture loads, but a lower displacement is achieved when fiber posts with a high elastic modulus and metallic posts are used.

Objetivo: Este trabalho avaliou a carga para fratura e deslocamento de raízes restauradas com pinos de diferentes módulos de elasticidade. Material e método: Trinta e seis réplicas de microfibras de vidro embutidas em resina epóxi foram fabricadas a partir de uma raiz de um pré-molar tratado endodonticamente preparado em 12 mm de comprimento com brocas customizadas, deixando 4 mm apicais sem preparo. As raízes foram randomicamente restauradas com (n = 12): FP-LM (pino de fibra com um baixo módulo de elasticidade - 50 GPa), FP-HM (pino de fibra com um alto módulo de elasticidade - 67 GPa) e MP (pinos metálicos - 208 GPa), usando adesivo autopolimerizável e cimento resinoso dual. Núcleos foram confeccionados com resina composta e coroas metálicas foram cimentadas em todas as raízes com cimento resinoso autoadesivo com modo de polimerização químico. Os espécimes foram submetidos ao teste de fratura em 45° (inclinação de 45° / 0,5 mm/min) e o deslocamento foi registrado aos 100 N. Resultado: Anova 1 fator mostrou que o módulo de elasticidade dos retentores não afetou as médias de fratura (p = 0,203) (FP-LM: 237,4 ± 65,11 N; FP-HM: 236,7 ± 92,85 N; MP: 295,8 ± 108,7 N) mas foi estatisticamente significante para o deslocamento (p < 0,00): o teste de Tukey mostrou que a média de deslocamento do grupo FP-LM (0,81 ± 0,15 mm) foi significativamente maior do que o grupo FP-HM (0,46 ± 0,26 mm; p = 0,00) e MP (0,62 ± 0,07 mm; p = 0,47). Conclusão: Pinos com diferentes módulos de elasticidade mostram resistência similar, porém um menor deslocamento é obtido quando pinos de fibra com alto módulo de elasticidade (FP-HM/MP) são usados.

Clinical performance and failure modes of pulpless teeth restored with posts: a systematic review

Abstract The aim of this systematic review was to compare the clinical performance and failure modes of teeth restored with intra-radicular retainers. A search was performed on PubMed/Medline, Central and ClinicalTrials databases for randomized clinical trials comparing clinical behavior and failures of at least two types of retainers. From 341 detected papers, 16 were selected for full-text analysis, of which 9 met the eligibility criteria. A manual search added 2 more studies, totalizing 11 studies that were included in this review. Evaluated retainers were fiber (prefabricated and customized) and metal (prefabricated and cast) posts, and follow-up ranged from 6 months to 10 years. Most studies showed good clinical behavior for evaluated intra-radicular retainers. Reported survival rates varied from 71 to 100% for fiber posts and 50 to 97.1% for metal posts. Studies found no difference in the survival among different metal posts and most studies found no difference between fiber and metal posts. Two studies also showed that remaining dentine height, number of walls and ferrule increased the longevity of the restored teeth. Failures of fiber posts were mainly due to post loss of retention, while metal post failures were mostly related to root fracture, post fracture and crown and/or post loss of retention. In conclusion, metal and fiber posts present similar clinical behavior at short to medium term follow-up. Remaining dental structure and ferrule increase the survival of restored pulpless teeth. Studies with longer follow-up are needed.

Mechanical behavior of yttria-stabilized tetragonal zirconia polycrystal: Effects of different aging regimens

Abstract This study aimed to characterize and compare the effect of different aging regimens on surface characteristic (topography and roughness), structural stability (phase transformation) and mechanical performance (Weibull analysis) of a Y-TZP ceramic. Discs (15 × 1.2 mm; VITA In-Ceram YZ) were prepared according to ISO 6872-2015 for biaxial flexural strength testing and randomly assigned into five groups (n = 30): as-sintered, no aging treatment (CTRL); 20 h in autoclave at 134°C, 2 bar pressure (AUT); intermittent mechanical loading at 20 Hz/106 load pulses (MechLoad); AUT followed by MechLoad (AUT+MechLoad); and storage in distilled water at 37°C, for 1 year (STO). The following analyses were performed: roughness (n = 30), surface topography (n = 2), phase transformation (n = 2) and biaxial flexure strength (n = 30). Phase transformation (increase of m-phase content) was shown to be a spontaneous, unavoidable and time-dependent process, occurring even under ambient conditions (dry storage after 1 year = 6.0% increase), and is considerably accelerated in the presence of moisture (STO = 17.6%; AUT= 63.1%; and AUT+MechLoad = 59.9%). For roughness parameters, only Ra was affected by aging, and the highest values were observed for AUT+MechLoad (0.25 ± 0.07 µm). For Weibull analysis, structural reliability (Weibull moduli) and characteristic strength were not impaired after aging, and some aging conditions led to increased values (highest weibull moduli in AUT, and highest characteristic strength in STO). Phase transformation proves to be a time-dependent spontaneous mechanism that is accelerated in the presence of different stimuli. However, none of the aging regimens had a negative effect on the characteristic strength and structural reliability of Y-TZP ceramic.

Influence of periodontal ligament simulation on bond strength and fracture resistance of roots restored with fiber posts

Objective: Considering that periodontal ligament simulation may influence the stress distribution over teeth restored with intraradicular retainers, this study aimed to assess the combined effect of mechanical cycling and periodontal ligament simulation on both the bond strength between fiber posts and root dentin and the fracture resistance of teeth restored using glass fiber posts. Material and Methods: Ninety roots were randomly distributed into 3 groups (n=10) (C-MC: control; P-MC: polyether; AS-MC: addition silicone) to test bond strength and 6 groups (n=10) (C: control; P: polyether; AS: addition silicone, without mechanical cycling, and C-MC, P-MC and AS-MC with mechanical cycling) to test fracture strength, according to the material used to simulate the periodontal ligament. For the bond strength test, fiber posts were cemented, cores were built, mechanical cycling was applied (2×106 cycles, 88 N, 2.2 Hz, and 45º incline), and the teeth cut into 3 slices (2 mm), which were then subjected to the push-out test at 1 mm/min. For the fracture strength test, fiber posts were cemented, cores were built, and half of the groups received mechanical cycling, followed by the compressive strength (45° to the long axis and 1 mm/min) performed on all groups. Results: Periodontal ligament simulation did not affect the bond strength (p=0.244) between post and dentin. Simulation of periodontal ligament (p=0.153) and application of mechanical cycling (p=0.97) did not affect fracture resistance. Conclusions: The materials used to simulate the periodontal ligament did not affect fracture or bond strength, therefore periodontal ligament simulation using the tested materials could be considered optional in the conditions of the study. .

Surgical treatment of transmigration of mandibular canine

Introduction: The occurrence of canine impaction is not a rare phenomenon, but transmigration of the tooth across the midline is a less common event. The finding is normally asymptomatic and the etiologic factors involved in the transmigration process are still unclear. Objective: To present a clinical case of surgical treatment of a transmigrated mandibular canine. Case report: A 17-year-old male patient presented to the dental clinic to remove an unerupted canine. Clinical and radiological examinations led to the diagnosis of a transmigrated canine in the mental region. Surgical removal was the treatment of choice and further radiographs were needed to complement the clinical exam and to determine the location of the tooth precisely for the surgical procedure. Postoperative period was uneventful. Canine transmigration is a rare finding and symptoms are usually absent. Conclusion: An early detection is important to plan the treatment and mainly to avoid future complications.